| 1. |
- Larsson, Anton, 1984, et al.
(author)
-
Evaluation of Performance of Industrial-Scale Dual Fluidized Bed Gasifiers Using the Chalmers 2–4-MWth Gasifier
- 2013
-
In: Energy & Fuels. - : American Chemical Society (ACS). - 1520-5029 .- 0887-0624. ; 27:1, s. 6665-6680
-
Journal article (peer-reviewed)abstract
- A general approach to evaluating the performance of industrial-scale dual fluidized bed (DFB) gasifiers was developed in this work. The approach is intended to simplify comprehensive evaluation of DFB gasifiers and to highlight important parameters, some of which are often missed or omitted in the literature. By applying this procedure, experimental results can be generalized, which is verified in this work using the Chalmers 2–4-MWth DFB gasifier. In a DFB gasifier, some of the fuel is converted to the desired calorific gas, while the remaining portion is combusted to meet the heat demands of the process. As shown here, the total heat demands limit the amount of chemical energy that can be restored from the fuel into the produced gas, whereby the main heat demands are from the drying and heating of the fuel, in addition to heating the combustion air and steam. By establishing a heat balance across the system, the chemical efficiency can be estimated. With lower heat demands, higher chemical efficiency is achievable, whereas with higher heat demands, more of the fuel must be burned and a lower chemical efficiency is achieved. It is experimentally complicated to quantify the level of fuel conversion and heat demands of a DFB gasification system. In this work, an experimental procedure is presented and implemented using the Chalmers gasifier to quantify the fuel conversion and heat demands. Furthermore, it was investigated how a variation in the amount of steam used for fluidization of the gasifier affects fuel conversion and other important parameters. To establish a reference case, silica sand was used as bed material and wood pellets was used as fuel to minimize the effects of ash and the bed material. By increasing the level of fluidization steam, the average residence time of the gas was decreased and the gas temperature, gas velocity, and steam-to-fuel ratio were increased, which resulted in increased conversion (up to 36%) of organic compounds (OC). However, limited char conversion was achieved (0%–4%), and the chemical efficiency remained unaffected by the amount of steam added to the process. The chemical efficiency of the Chalmers gasifier was determined to be 74% when using wood pellets as fuel. This is comparable to results from thermo-economic modeling of second-generation biofuels production processes, which, based on the heat demand, report the chemical efficiency of the DFB gasifier as being in the range of 74%–77% to maximize the overall efficiency. This shows that the required chemical efficiency is achieved, even with low char conversion, when using a fuel with a high content of volatiles, such as wood pellets.
|
|
| 2. |
- Neves, Daniel Santos Felix, 1982, et al.
(author)
-
Method for online measurement of the CHON composition of raw gas from biomass gasifier
- 2014
-
In: Applied Energy. - : Elsevier BV. - 1872-9118 .- 0306-2619. ; 113, s. 932-945
-
Journal article (peer-reviewed)abstract
- For unattended biomass gasification processes, rapid methods for monitoring the elemental composition (CHON) of the raw gas leaving the gasifier are needed. Conventional methods rely on time-consuming and costly laboratory procedures for analysing the condensable part of the raw gas. An alternative method, presented in this work, assesses the CHON composition of raw gas in a "one step" analysis without the need to previously characterise its chemical species composition. Our method is based on the quantitative conversion of a raw gas of complex chemical composition into CO2, H2O, and N2 in a small combustor. The levels of these simple species can be measured with high accuracy and good time resolution, and the CHON composition of the raw gas can be determined from the mass balance across the combustor. To evaluate this method, an online combustion facility was built and used to analyse the raw gas from the Chalmers 2-MWth dual fluidised bed steam gasifier. Test runs of the developed facility demonstrated complete combustion of the raw gas and the measurements were both fast and reliable. The new method used in combination with zero-dimensional reactor modelling provides valuable data for the operational monitoring of gasification processes, such as the degree of fuel conversion, composition of the char exiting the gasifier, oxygen transport by catalytic bed material, and amount of condensables in raw gas.
|
|
